Industry new

Rivet Nuts in Communication Equipment: Applications and Selection Notes

Rivet Nuts in Communication Equipment: Applications and Selection Notes

Telecom is among the largest consumers of rivet nuts: cabinet columns, equipment chassis, power module plates, antenna and RRU brackets at base stations. Countless thread points land on thin sheet metal, and many of them need repeated disassembly during on-site installation and later maintenance. Rivet nuts turn thin sheet into a load-bearing thread base with flexible processing and a flush back side, matching telecom sheet-metal practice naturally. Serving this industry for years, FASTKING reviews the applications and selection notes.

Why Rivet Nuts Fit Telecom Cabinets

Cabinet structure dictates fastener choice: thin sheet (mostly under 1.5 mm), numerous dispersed thread points, and positions inside closed cavities or already-bent boxes where welding and press equipment cannot reach. A rivet nut needs one-side access only; a riveting tool completes installation at any reachable hole, unconstrained by cavities or press availability. Rework installation after coating is possible without damaging paint. This one-sided, flexible, late-stage-installable character makes rivet nuts the default for downstream thread points in telecom sheet metal.

A Map of Typical Locations

In cabinets: rack-mounted equipment mounting holes on columns and rails use rivet nuts extensively, especially late-installed mounting plates; door and side-panel hinges and locks use larger-thread rivet nuts that carry repeated opening loads. In chassis: power and control module plates, fan brackets and cable trays installed after box forming showcase the one-side advantage. At base stations: antenna pole brackets and RRU mount adjustment holes, where outdoor service adds material and corrosion requirements. Knowing these locations enables graded selection by position.

Materials and Finish: The Room Is Not Neutral

Telecom environments are more complex than assumed: equipment rooms are conditioned, but battery acid mist and dust are not rare; outdoor stations face humidity, coastal salt spray and industrial pollution. Indoors, zinc-plated steel covers most cases; outdoor and coastal sites justify stainless rivet nuts, or at least a corrosion class agreed jointly between fastener and sheet; aluminum rivet nuts inside aluminum chassis avoid galvanic couples. Remember: the rivet nut and sheet are a permanent pair, so corrosion class must be judged by the weaker of the two. A plated part on an aluminum panel outdoors starts failing from the sheet side.

Sheet Thickness and Riveting Fit

Rivet nuts have defined thickness ranges, and the most common selection error is choosing by thread size while ignoring sheet fit. Below the minimum, the riveting section cannot deform enough and pull-out and torsion capacity fall; above the maximum, it cannot set fully. Telecom's typical 0.8 to 1.5 mm sheet falls within standard ranges, but aluminum and stainless differ in hardness and plasticity, so verify ranges per material. Hole tolerance and burr condition are equally critical variables and should map one-to-one to the rivet model in process documents.

Thread Size and Load Checking

Telecom cares about long-term reliability: cabinets stand for years, and a thread point that gradually loosens or pulls out under vibration risks toppled equipment and signal loss. Check each rivet point's axial load and moment against the mounted unit's weight, center of gravity and vibration class, keeping margin against the nut's rated pull-out and torque-out. When several nuts share a load, also balance hole placement; holes too close together stack stress locally and reduce overall capacity. For suspended heavy items, review loads with the fastener supplier at the sheet-design stage.

Tools and Site Efficiency

Installation tools split into pneumatic and manual. Lines use pneumatic riveters for speed and stable pull force; field maintenance uses hand tools, portable but prone to under-setting when pull force runs low. Tool choice also affects reachability: nosepiece size decides whether holes near bends and deep cavities are installable, so confirm access at design time for dense hole patterns. Air pressure stability directly affects quality, and bottle supply or long hoses demand attention to end-of-line pressure.

Loosening and Maintenance

Long service life with short maintenance cycles shapes the locking approach. Standard practice: mount bolts to spec torque and re-tighten on the maintenance schedule; for stronger vibration, as on outdoor antenna brackets, add spring washers or thread adhesive. A rivet nut cannot be replaced once failed; rework means new holes, so generous load margins and avoiding over-torque are the best maintenance strategy. Marking rivet models and recommended torques on drawings helps technicians years later.

Supplier Support and Customization

Beyond standard specs, telecom requests include custom lengths, special heads such as countersunk for visible faces, and low-resistance grounding requirements. Custom responsiveness and batch consistency both matter. FASTKING serves telecom customers with standing stock of common sizes, fast sampling for custom drawings, and material and plating records per batch, helping equipment makers manage this small-but-numerous thread-point layer steadily and economically.

CONTACT US

Contact: Mr. Deng

Phone: 13928071304

Tel: 0756-8586520

Email: lizhong@zhjiali.com

Add: 102, Building 4, No. 4 Fuyuan Road, Waisha Village, Shenwan Town, Zhongshan City, Guangdong Province,China