Science and technology

Rivet Nut Pull-out and Torque Strength on Thin Sheet: Values and Verification

Rivet Nut Pull-out and Torque Strength on Thin Sheet: Values and Verification

A common selection error is treating rivet nut load capacity as a property of the nut. The same nut installed in two millimetre cold-rolled steel and in one millimetre aluminium can differ several-fold in pull-out strength. The reason is simple: a rivet nut interlocks through plastic deformation of the sheet, so what actually resists load is the compressed sheet material, with the nut only transferring force into it. Understand that and design values stop drifting.

What the two strength figures mean

Pull-out strength is the axial force needed to eject the nut, testing the shear and bending capacity of the sheet in the interlock zone. Torque strength is the torque at which the nut begins to rotate relative to the panel, testing interface friction and knurl penetration. Failure modes differ: pull-out shows as the sheet tearing or bulging, torque failure as the nut slipping in the hole. Choose the governing figure by actual loading - pull-out for tensile joints, torque for joints opened repeatedly.

What drives pull-out strength

Four factors dominate: sheet thickness, sheet strength, interlock annulus area, and whether the deformation zone opened completely. Thicker sheet means a larger shear section, so strength rises roughly linearly. Higher sheet strength carries more per unit area, but too high prevents adequate deformation during setting. Annulus area follows head diameter and setting-zone geometry. Incomplete opening discounts effective area. The most effective improvement is usually thicker sheet or a larger head, not a stronger nut material.

What drives torque strength

Torque strength depends more on interface detail: how tightly the setting zone conforms to the hole wall, how firmly the head compresses the panel, and the friction coefficient between them. Oil, paint or thick plating on the sheet reduces friction and torque strength; a nut not fully seated leaves insufficient contact area and slips as well. That is why the same lot performs differently on different lines. For frequently opened joints, control installation quality and surface cleanliness alongside selection.

The accompanying problem of sheet distortion

Thin-sheet riveting carries a hidden risk: panel distortion. Setting stretches the sheet locally, producing slight dishing or undulation that is hard to see but enough to affect flatness and sealing. Under load the distortion grows, showing as bulging around the nut, uncompressed gasket and loosening at adjacent fastening points. Place nuts where stiffness is higher - near bends or ribs - or add local reinforcement. On flatness-critical panels this deserves more attention than strength.

Test methods and criteria

Strength data must be measured, not copied from a catalogue. A pull test applies axial force with a tensile machine, recording peak load and failure mode; a torque test loads gradually with a torque wrench or transducer, recording the moment rotation begins. Use coupons at the customer's actual thickness and material, with several pieces per group, and record scatter as well as mean. Apply a safety factor: a fraction of measured value for static joints, lower for dynamic or safety-related ones, with margin for corrosion and fatigue.

Conservative design principles

Three principles apply. First, calculate with the lower limit of sheet thickness, since incoming material often runs thin. Second, use the minimum of the batch test data rather than the mean - wide scatter indicates an unstable process. Third, allow for long-term effects: riveted joints relax under sustained load, particularly in aluminium and thin sheet, with residual clamp force falling over years. For critical joints, run a load-hold test on prototypes to observe change over time, not just instantaneous failure.

How assembly process decides final strength

With the same nut and sheet, process variation changes strength substantially. Insufficient pulling force, short stroke, worn mandrel, burred hole edges and oily surfaces all leave the interlock incomplete. Strength is therefore a process control issue as much as a design one: define force and stroke, calibrate tools on schedule, specify deburring and cleanliness, and verify the first unit each shift. Written into work instructions, measured strength becomes repeatable and design values hold.

Closing: strength is a system property

Pull-out and torque strength result from nut, sheet, hole size and installation process together - change any one and the conclusion changes. Design to the lower thickness limit and the minimum measured value, verify with real coupons on both pull and torque, and freeze the process parameters in production. We support customers with strength testing and selection advice so values are settled at prototype stage rather than assumed.

CONTACT US

Contact: Mr. Deng

Phone: 13928071304

Tel: 0756-8586520

Email: lizhong@zhjiali.com

Add: 102, Building 4, No. 4 Fuyuan Road, Waisha Village, Shenwan Town, Zhongshan City, Guangdong Province,China